manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 20 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 20

Partially filled pipes

For partially filled pipes or pipes with downwards flow and free outlet, sensor must be mounted 

in a U-tube.

4.1.2

Orienting the sensor

MAG 8000 CT DN 50 to DN 150 can be installed in all orentations, while DN 200 to DN 400 

can only be installed horizontally.

Horizontal pipes

Sensor must be mounted as shown in upper part of figure. Do not mount sensor as shown in 

lower part of figure as electrodes then will be positioned at top where air bubbles may occur 

and in bottom, where mud, sludge, sand etc. may deposit and cover the electrode, thus 

impacting the measurement.
If "Empty Pipe Detection" is used, sensor should be tilted 45° as shown in upper right figure 

to maximize full pipe detection and provide accurate volume calculations.

Note
Physical installation of battery pack may influence battery capacity. Optimal battery capacity 

is achieved with battery pack in an upright position. Installation examples marked with dotted 

cross will affect battery capacity.

Installing/Mounting
4.1 Sensor installation

SITRANS MAG 8000

20

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments