manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 139 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 139

C.2.3

200-299

Param‐

eter ID

Meter
version

Display
view

Parameter/data type

Factory settings

Data range

 

 

 

 

Fixed parameter or meter data that are not changeable

200

All

O4

Fault status

No faults

0 to 8191, binary presented with 

information 1 for bit 0
1: Insulation error
2: Coil current error
3: Amplifier overload
4: Database checksum error
5: Low power warning
6: Flow overflow warning
7: Pulse A overload warning
8: Pulse B overload warning
9: Consumption interval warning
10/L: Leakage warning
11/E: Empty pipe warning
12/C: Low impedance (high con‐

ductivity) warning
13/d: High flow limit warning
14/A: Reverse flow warning
If no error/warning is pending, 

the message is "No faults"

201

All

-

Alarm configuration list

254 = Alarm 2 to 8 enabled 0 to 8191, See 200

If no alarm is enabled, the mes‐

sage is "None enabled"

202

All

-

Date of fault log reset

PS3 production date and 

time

year-month-day T hours:mi‐

nutes:seconds

203

All

O4

Non optimal measure time, in‐

cluding the time of device run‐

ning with insulation test fault, 

coil current fault, amplifier 

fault, database checksum 

fault, flow overload fault, or 

empty pipe fault.

0

 

204

All

-

Reset the fault log and faults

No

Yes / No

Value is reset to "No" when up‐

loading device parameters to pc 

after command execution

205

All

-

Call up acknowledge

No

Yes / No 

Value is reset to "No" when up‐

loading device parameters to pc 

after command execution

206

All

-

Battery alarm level

10%

0 to 100%

Appendix

C.2 Parameter lists

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

139

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments