Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 104

Page: 104 / 164

Size

50 (2")

65 (2½") 80 (3")

100 (4")

125 (5")

150 (6")

200 (8")

250 (10") 300 (12")

Q2 [m

/h]

0.25

0.4

0.63

1.6

2.5

6.4

Q1 [m

/h]

0.16

0.25

0.4

0.63

1.6

2.5

10.10

MAG 8000 CT (7ME6820) (Revenue program) MI-001

MAG 8000 CT program is type approved according to international water meter standard OIML

R49. Since 1 November 2006 the MI-001 water meter directive has been in force, which means

that all water meters can be sold across the EU borders if the water meters contain a MI-001

label.
The MAG 8000 CT MI-001 verified and labeled products are a Class II approval according to

Directive 2014/32/EU of the European Parliament and Council of February 26, 2014 on

measuring instruments (MID), Annex MI-001 in the sizes from DN 50 to DN 600.
The MID certification is obtained as a module B and module D approvals according to the

above mentioned directive.
Module B : Type approval according to OIML R49
Module D : Quality insurance approval of production

MAG 8000 CT MI-001 verified and labelled products at a given Q3 and Q4/Q3 = 1.25 and Q2/

Q1 = 1.6 measuring ranges se below table:

Size

(2")

(2½")

(3")

100

(4")

125

(5")

150

(6")

200

(8")

250

(10")

300

(12")

350

(14")

400

(16")

450

(18")

500

(20")

600

(24")

"R" Q

/Q1 25

Q4 [m

/h] 20

31.25 50

78.75 125

200

312.5 500

787.5 787.5 1250

1250 2000 2000

Q3 [m

/h] 16

100

160

250

400

630

1000

1000 1600 1600

Q2 [m

/h] 0.96 1.6

2.6

4.03

6.4

10.24 16

25.6

40.3

102.4 102.4

Q1 [m

/h] 0.6

1.6

2.52

6.4

25.2

Size

(2")

(2½")

(3")

100

(4")

125

(5")

150

(6")

200

(8")

250

(10")

300

(12")

350

(14")

400

(16")

450

(18")

500

(20")

600

(24")

"R" Q

/Q1 63

Q4 [m

/h] 20

31.25 50

78.75 125

200

312.5 500

787.5 1250

1250

3125 3125 5000

Q3 [m

/h] 16

100

160

250

400

630

1000

2500 2500 4000

Q2 [m

/h] 0.41 0.63

1.02 1.6

2.54

4.06

6.35

10.16 16

25.4

63.49 63.49 101.6

Q1 [m

/h] 0.25 0.4

0.63 1

1.59

2.54

3.97

6.35

15.9

39.68 39.68 63.49

Technical data
10.10 MAG 8000 CT (7ME6820) (Revenue program) MI-001

SITRANS MAG 8000

104

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews:

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 104 / 164

Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews: