Siemens SITRANS F M MAG 3100 Operating Instructions Manual Download Page 82

Page: 82 / 90

WARNING

Empty pipe detection

The installation has to fulfill the following limitations for usage of the empty pipe detection
function:
• media conductivity ≥ 20 μS/cm
• length of cable at remote installation ≤ 50 (150 ft)
• special shield cable must be used

Note for MAG 1100 sizes DN 2 and DN 3:
• empty pipe detection is not available
• media conductivity ≥ 30 μS/cm

Note for MAG 5000/6000 CT (FW 3.03):
• empty pipe detection is not available

9.4

Liner selection

Table 9-13

Liner

Applications

EPDM

Drinking Water, Low abrasive media, Food & Beverage

Ebonite

Drinking Water, Wastewater, Fine low abrasive media

PTFE

Drinking Water, Wastewater, Chemicals, Food & Beverage, Pulp
& Paper

PFA

Drinking Water, Wastewater, Chemicals, Food & Beverage, Pulp
& Paper

Linatex

Abrasive media

Soft rubber

Drinking Water, Wastewater, Abrasive media, Chemicals

9.5

Electrode selection

Table 9-14

Electrodes

Applications

Chemical Resistance

Stainless Steel

Drinking Water, Wastewater, Chemi‐
cals, Food & Beverage, Pulp & Paper

Reducing acids, Oxidicing acids, Or‐
ganic acids, Alkalis, Diluted salts

Hastelloy C22

Drinking Water, Wastewater, Abrasive
Liquids, Chemicals, Food & Beverage,
Pulp & Paper

Reducing acids, Oxidicing acids, Or‐
ganic acids, Alkalis, Diluted salts

Hastelloy C267

Drinking Water, Wastewater, Abrasive
Liquids, Chemicals, Food & Beverage,
Pulp & Paper

Reducing acids, Oxidicing acids, Or‐
ganic acids, Alkalis, Diluted salts

Technical specifications
9.5 Electrode selection

SITRANS FM MAG 3100

Operating Instructions, 12/2021, A5E03005599-AE

Summary of Contents for SITRANS F M MAG 3100



























































































Search results

Summary of Contents for SITRANS F M MAG 3100

Reviews:

Siemens SITRANS F M MAG 3100, Operating Instructions Manual, Page: 82 / 90

Search results

Summary of Contents for SITRANS F M MAG 3100

Reviews: