manualshive.com logo in svg

Siemens SITRANS F M MAG 3100, Operating Instructions Manual, Page: 33 / 90

Share
Download
Siemens SITRANS F M MAG 3100 Operating Instructions Manual Download Page 33

4.3.2

Torque values

Torque calculations

CAUTION

Overtightened bolts

Leakage/damage to flowmeter or piping may arise if bolts are overtightened.

All values are theoretical and are calculated on the assumption that:

• All bolts are new and material selection is according to EN 1515-1 table 2.

• Gasket material not exceeding 75 shore A is used between the flowmeter and mating flanges.

• All bolts are galvanized and adequately lubricated.

• Flanges are made of carbon steel.

• Flowmeter and mating flanges are correctly aligned.

Torque values

Note
Conversion to F/Lbs

To convert the torque values from Nm to F/Lbs multiply by 0.74.

Table 4-1

Minimum and maximum torques for EN 1092-1 PN 6 to PN 16 in Nm

Nominal 
size

EN 1092-1

PN 6

PN 10

PN 16

Liner

PFA, PTFE, 
Ebonite

Soft rubber, 
EPDM, Linatex

PFA, PTFE, 
Ebonite

Soft rubber, 
EPDM, Linatex

PFA, PTFE, 
Ebonite

Soft rubber, 
EPDM, Linatex

mm

inch Min

Max

Min

Max

Min

Max

Min

Max

Min

Max

Min

Max

15

½

-

-

-

-

-

-

-

-

-

-

-

-

25

1

-

-

-

-

-

-

-

-

-

-

-

-

32

1¼

-

-

-

-

-

-

-

-

-

-

-

-

40

1½

-

-

-

-

-

-

-

-

-

-

-

-

50

2

-

-

-

-

-

-

-

-

-

-

-

-

65

2½

3.9

4

3.2

4

-

-

-

-

8.5

9

6.9

7

80

3

6.9

7

5.7

6

-

-

-

-

10.8

11

8.8

9

100

4

10.3

11

8.7

9

-

-

-

-

13.8

14

11.6

12

125

5

6.4

7

5.5

6

-

-

-

-

19.2

20

16.5

17

150

6

8.1

9

7.2

8

-

-

-

-

29.8

31

26.1

27

Installing/Mounting

4.3 Mounting

SITRANS FM MAG 3100
Operating Instructions, 12/2021, A5E03005599-AE

33

Summary of Contents for SITRANS F M MAG 3100



























































































Reviews:

No comments