manualshive.com logo in svg

Siemens SITRANS F FUE380, Operating Instructions Manual, Page: 73 / 102

Share
Download
Siemens SITRANS F FUE380 Operating Instructions Manual Download Page 73

Troubleshooting/FAQs

9

9.1

Error codes

A list of error codes is available in SIMATIC PDM (active errors are check-marked). Access to 

this list is gained via [Device → Device Status] in parameter 200 

Fault status.. In the figure 

below, error code F 5 is active.

Figure 9-1

List of error codes shown in PDM

Table 9-1

Error codes shown in the display and in PDM 

Error 

code

Error

Remedy/Cause

Blank 

display

Battery plug not connected, or battery 

empty, mains power interrupted

● Check flowmeter version. Battery version not 

able to run on mains power

● Battery empty: Replace battery pack
● Battery plug not plugged into the transmitter, 

see Battery replacement (Page 63)

F 1

Path 1 (upper path) not measuring

No water in upper part of pipe and/or cables or 

transducer 1A or 1B defective

F 2

Path 2 (lower path) not measuring

No water in lower part of pipe and/or cables or 

transducer 2A or 2B defective

F 3

Internal software failure

Contact Siemens customer support

F 4

Internal software failure

Contact Siemens customer support

F 5 

Power supply warning

● Mains power fails (only mains-powered 

versions with battery back-up)

● Replace battery pack (battery-powered 

versions only)

FUS380/FUE380

Operating Instructions, 09/2016, A5E00730100-AB

73

Summary of Contents for SITRANS F FUE380







































































































Reviews:

No comments