Siemens SITRANS F FUE380 Operating Instructions Manual Download Page 27

Page: 27 / 102

For media temperatures above 120 °C (248 °F) only remote installation is allowed.

Temperatur specifications for non-insulated sensors

10-

100

140

200

FUS 380

FUE 380

0HGLDWHPSHUDWXUHr&

①

Compact and remote versions

②

Remote versions only

Temperatur specifications for insulated sensors

0LQPP

0HGLDWHPSHUDWXUHr&

10-

100

140

200

FUS 380

FUE 380

①

Keep terminal box free from insulation (gray area)

②

Insulation

①

Compact and remote versions

②

Remote versions only

4.3

Transmitter installation (compact/remote versions)

The transmitter is packed separately - ready for plug-in into base part.

Installing/Mounting

4.3 Transmitter installation (compact/remote versions)

FUS380/FUE380

Operating Instructions, 09/2016, A5E00730100-AB

Summary of Contents for SITRANS F FUE380







































































































Search results

Summary of Contents for SITRANS F FUE380

Reviews:

Siemens SITRANS F FUE380, Operating Instructions Manual, Page: 27 / 102

Search results

Summary of Contents for SITRANS F FUE380

Reviews: