manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 80 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 80

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8539

Float / 4

Standard vol‐

ume lower 

alarm limit

Falling below this limit 

causes an alarm when 

volume flow is selected 

as input.

Min. floating 

point value

[Sl]

(8522)

 

Read / 

write

8541

Float / 4

Standard vol‐

ume alarm hys‐

teresis

Hysteresis that affects 

the alarm and warning 

limits when volume 

flow is selected as in‐

put.

0.0

[Sl]

(8522)

-

Read / 

write

4.10.5.8

Inputs and outputs

General channel 2 settings

Table 4-30

General channel 2 settings   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8801

Unsigned / 2

Operation mode Operation mode.

0

● 0: Off
● 1: Current output
● 2: Frequency output
● 3: Pulse output
● 4: Signal output

Read / 

write

7420

Unsigned / 2

Active/passive 

operation

Shows application pos‐

sibilities.

-

● 0: Active operation 

not possible, use 
passive wiring!

● 1: Active operation 

possible, hardware is 
able to drive the 
current loop.

Read 

only

9590

Unsigned / 2

Fail-safe activa‐

tion condition

Fail-safe activation con‐

dition.

1

● 0: Bad status of 

selected process 
value

● 1: Active 

Maintenance alarm 
or Failure (NAMUR)

Read / 

write

8981

Unsigned / 2

Fail-safe min. 

time

Minimum time the out‐

put stays in fail-safe be‐

havior.

0

[s]

0 - 100

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

80

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments