manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 7 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 7

Introduction

1

1.1

Purpose of this documentation

This manual contains all information needed to integrate the process instruments into a 

communications network. The manual is aimed at control system designers, system 

integrators, instrument engineers. 
In order to operate safety and for more detailed information you need the product specific 

manual. Available for download from Flow documentation (

http://www.siemens.com/

flowdocumentation

).

This manual applies to the SITRANS FCT030 transmitter Modbus version only. The FCT030 

transmitter can be used in combination with the following sensors: 
Mass 2100
FC300  
FCS400 and FSC300
In order to operate a Coriolis flow meter, you also need Operating Instructions. See Flow 

documentation (

http://www.siemens.com/flowdocumentation

)

1.2

Document history

The following table shows major changes in the documentation compared to the previous 

edition. 
The most important changes in the documentation when compared with the respective 

previous edition are given in the following table.

Edition

Note

06/2018

Second edition

06/2017

First edition

Use the device to measure process medium in accordance with the information in the 

Operating Instructions.

Note
Use in a domestic environment
This Class A Group 1 equipment is intended for use in industrial areas. 
In a domestic environment this device may cause radio interference.

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

7

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments