Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 36

Page: 36 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access lev‐

10307

Unsigned / 4 Modbus coil bit‐

mask 2

Bit mask which is compared

against the register value

specified with Modbus coil reg‐

ister 2 to determine the coil

value. If any bit of the register

value is set which is also set

in the bit mask then the coil

value is true otherwise false.

0 - 4294967295 Read / write

10309

Unsigned / 2 Modbus coil

length 2

Output parameter that informs

about size in bytes of parame‐

ter that is specified by Modbus

coil address 2. Could be used

to identify the relevant bits of

the Modbus coil bitmask 2

Read only

...
10399

Unsigned / 2 Modbus coil

length 20

Output parameter that informs

about the size in bytes of the

parameter that is specified by

Modbus coil address 20.

Could be used to identify the

relevant bits of the Modbus

coil bitmask 20

Read only

If default value is "-" the command "Set to default" will not set this parameter to default.

4.4

Modbus register mapping

The device provides the possibility to map each existing parameter to a freely chosen Modbus

MODBUS commands
4.4 Modbus register mapping

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 36 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: