manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 35 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 35

4.3

Coil configuration

The device provides 20 coil definitions which can be configured. 

Table 4-2

Coil configuration   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units] 

1

(units register)

Value range / 

Setting options

Access lev‐

el

10300

Unsigned / 2 Modbus coil ad‐

dress 1

Specifies the coil address with 

which the following bit coded 

register value is accessible. 

The register and bit(s) are 

specified by Modbus coil reg‐

ister 1and Modbus coil bit‐

mask 1

1

0 - 65535

Read / write

10301 

Unsigned / 2 Modbus coil 

register 1

Specifies the Modbus register 

whose value is checked 

against Modbus coil bitmask 1 

to determine the coil value 

(false or true). A register value 

of 65535 specifies that this coil 

mapping is undefined.

Undefined

0 - 65535

Read / write

10302

Unsigned / 4 Modbus coil bit‐

mask 1

Bit mask which is compared 

against the register value 

specified with Modbus coil reg‐

ister 1 to determine the coil 

value. If any bit of the register 

value is set which is also set 

in the bit mask then the coil 

value is true, otherwise the 

coil is false.

0

0 - 4294967295 Read / write

10304

Unsigned / 2 Modbus coil 

length 1

Output parameter that informs 

about the size in bytes of the 

parameter that is specified by 

Modbus coil address 1. Could 

be used to identify the relevant 

bits of the Modbus coil bit‐

mask 1

-

 

Read only

10305

Unsigned / 2 Modbus coil ad‐

dress 2

Specifies the coil address with 

which the following bit coded 

register value is accessible. 

The register and bit(s) are 

specified by Modbus coil reg‐

ister 2 and Modbus coil bit‐

mask 2

2

0 - 65535

Read / write

10306

Unsigned / 2 Modbus coil 

register 2

Specifies the Modbus register 

whose value is checked 

against Modbus coil bitmask 2 

to determine the coil value 

(false or true). A register value 

of 65535 specifies that this coil 

mapping is undefined.

Undefined

 

Read / write

MODBUS commands

4.3 Coil configuration

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

35

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments