Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 188

Page: 188 / 198

4.10.12.3

FW update change log

Table 4-114 FW update change log

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

6900

Unsigned / 2

Newest entry

number

Entry number of new‐

est entry. Older entries

have a smaller entry

number.

(Wrap around for 0 -

100).

Read

only

6981

Unsigned / 2

Entry number

Selection of the entry

number.

0 - 20

Read /

write

6919

String / 16

Time stamp

Time stamp of the pa‐

rameter change log en‐

try specified by Entry

number.

Format is YYYY-MM-

DD hh-mm.

Read

only

6927

String / 16

Version

Version string specified

by Entry number.

Read

only

6952

Unsigned / 2

Available en‐

tries

Current number of

available firmware up‐

dates log entries.

Read

only

6953

Unsigned / 2

Clear parame‐

ter change log

Command to clear the

parameter change log.

● 0:Cancel
● 1: Clear log

Write on‐

ly (Ex‐

pert)

4.10.12.4

Device reset

Table 4-115 Device reset

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

700

Unsigned / 2

Set to default

Command to set all

changeable parame‐

ters to their defined val‐

ues.

● 0: Command not

running/command
done

● 1: Reset parameters

Write on‐

6000

Unsigned / 2

Restart device

Command to restart de‐

vice.

● 0: Command not

running/command
done

● 1: Restart device

Write on‐

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

188

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 188 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: