Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 166

Page: 166 / 198

Channel 2

Table 4-83

Channel 2

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

8803

Float / 4

Current output

value

Output current value if

configured to current

output.

Read

only

8828

Unsigned / 2

Error status

Error status if config‐

ured to current output.

● Bit 0: Overflow
● Bit 1: Underflow
● Bit 2: Fail mode

activated

● Bit 3: Cable break
● Bit 4: Output current

cannot be
established (read
back deviation > 0.1
mA)

Read

only

8840

Unsigned / 2

Status output

Status value if config‐

ured to status output.

Read

only

8969

Float / 4

Pulse status

output

Amount done if config‐

ured to pulse output.

Read

only

8972

Unsigned / 2

Error status

Error status if config‐

ured to pulse output.

● Bit 0: The pulse

putput has reached
the maximum pulse
output frequency

● Bit 1: Fail mode is

activated

Read

only

8987

Unsigned / 4

Pulse counter

Pulse output since

startup.

Read

only

8900

Float / 4

Frequency out‐

put value

Frequency value if con‐

figured to frequency

output.

Read

only

8903

Unsigned / 2

Error status

Error status if config‐

ured to frequency out‐

put.

● Bit 0: Overflow
● Bit 1: Underflow
● Bit 2: Fail mode

activated

Read

only

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

166

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 166 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: