Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 101

Page: 101 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9591

Unsigned / 2

Fail-safe activa‐

tion condition

Fail-safe activation con‐

dition.

● 0: Bad status of

selected process
value

● 1: Active

Maintenance alarm
or Failure (NAMUR)

Read /

write

9281

Unsigned / 2

Fail-safe min.

time

Minimum time the out‐

put stays in fail-safe be‐

havior.

[s]

0 - 100

Read /

write

9261

Unsigned / 2

Fail-safe behav‐

ior

Pulse output reaction in

case of a fault.

Only applicable if Re‐

dundancy mode (9280)

= 0.

● 0: Last valid value
● 1: Hold. Value 0.0

substitutes the actual
input value

● 2: Disabled
● 3: Custom value

Read /

write

7431

Float / 4

Fail-safe value

Output value in case of

a fault and when Fail-

safe behavior (9261) is

configured to 4.

0.0

[pulses/s]

0.0 - 12500.0

Read /

write

7158

Float / 4

Forced value

Forced value when

forcing is active.

1.0

[pulses/s]

0.0 - 12500.0

Read /

write

Channel 3 status output settings (relay)

Table 4-39

Channel 3 status output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9141

Unsigned / 2

Status mode

Select the functionality

for the status output.

● 0: Alarm class
● 1: Alarm item

Read /

write

9158

Unsigned / 2

Alarm class

Bit encoded selection

of alarm classes which

impact the status out‐

put. Each diagnostic

event is allocated to an

alarm class. See Alarm

items (Page 145).
Applicable if Status

mode = 0.

● Bit 0: Process value

alarm (PA)

● Bit 1: Process value

warning (PW)

● Bit 2: Maintenance

alarm (MA)

● Bit 3: Maintenance

warning (MW)

● Bit 4: Maintenance

required (MR)

● Bit 5: Function check

(FC)

Read /

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

101

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 101 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: