Siemens SITOP PSU3800 12 V/20 A User Manual Download Page 27

Page: 27 / 108

SITOP PSU8200/3800 3ph
Manual, 05.2018, C98130-A7638-A1-6-7629

Mounting position, mounting clearances

4.1

Standard mounting position

The device is mounted on standard mounting rails. The device must be mounted vertically in

such a way that the input terminals and the output terminals are at the bottom to ensure

correct cooling.
A clearance of at least 40 mm or 50 mm should be maintained above and below the device

(maximum depth of the cable duct, 50 mm).
No space is required at the side.

Output current as a function of the ambient temperature and mounting height

Figure 4-1

6EP3436-8SB00-0AY0: Output current in the standard mounting position

Figure 4-2

6EP1437-3BA10: Output current in the standard mounting position

Summary of Contents for SITOP PSU3800 12 V/20 A













































































































Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands

Siemens SITOP PSU3800 12 V/20 A, User Manual

Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands