Siemens SIRIUS 3RW44 Manual Download Page 42

Page: 42 / 292

Installation, connection and feeder configuration

4.5 Generator operation with three-phase asynchronous motor

3RW44 soft starters

Manual, 03/2017, NEB535219502000/RS-AB/008

4.5

Generator operation with three-phase asynchronous motor

The 3RW44 soft starters are suitable for generator operation.

NOTICE

Depending on the operating speed, connect the generator to the system while in the

subsynchronous (motor) range and slowly move the machine into the supersynchronous

range. Connecting the generator directly in the supersynchronous range may cause soft

starter faults.

4.6

Electrical connection

4.6.1

Control and auxiliary circuit connection

The SIRIUS 3RW44 soft starter is supplied with two different connection systems:

●

Screw connections

●

Spring-loaded connections

Two control voltage versions are available:

●

115 V AC

●

230 V AC

4.6.2

Main circuit connection

All soft starters have busbar connections for the main circuit connection.

Size 3RW44 2.

An additional box terminal for direct cable connection is supplied as standard with size

3RW44 2.

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands