Siemens SIRIUS 3RW44 Manual Download Page 140

Page: 140 / 292

3RW44 soft starters

140

Manual, 03/2017, NEB535219502000/RS-AB/008

Diagnostics and messages

8.1

Diagnostics and messages

8.1.1

Status messages

Message

Cause/solution

Check voltage

The main voltage is not yet applied.

Check the line phases

Option 1: Main voltage is applied, but the motor is not yet connected or is

not yet connected correctly.
Option 2: The motor is connected correctly, but there is no phase voltage.

Ready to start

Device is ready (main voltage is applied and motor is connected correctly).
The motor starts as soon as a start command is issued.

Starting active

Motor is started with the selected startup mode.

Motor running

Device is in bypass mode (bypass contactor). Start-up completed.

Coast down active

Motor is stopped with the selected coasting method.

Motor cooling time active (for devices with

product version < *E06*)

After an overload trip of the thermal motor model, starting of the motor is not

possible for a certain period of time (parameter: recovery time), to ensure

that the motor can cool down.

Switching element cooling time

(for devices with product version < *E06*)

After the device's intrinsic protection mechanism has tripped because of an

overload, the motor cannot be started for 30 s to allow the device to cool

down.

Emergency start active

The emergency start function is activated.

Quick stop active

The quick stop function is activated.

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands