Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 88 | Manualshive

Page: 88 / 128

Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 88

SIREMOBIL Iso-C

SPR2-230.061.01

Page 22 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 22

Replacing boards / replacing components

Centering the camera optics to the I.I. output

6

Prerequisite: The +220°, -220° and 0° positions were already marked as previously
described.

•

Rotate the camera optics back to the 0° position.

•

Loosen the three attachment screws of the camera optics slightly.

•

Loosen both eccentric screws adjacent to the camera optics slightly .

•

Move the camera optics toward the center, between both +220° and -220° markings (Re-
fer also to Fig. 9).

•

Switch fluoro on briefly and evaluate the position on the monitor.
According to the ratio of the I.I. input screen diameter to the I.I. output screen diameter, a
shift of the camera optics by approximately 0.1 mm corresponds to a position shift of the
washer displayed on the monitor of more than 1.7 mm (23 cm I.I.).

•

Secure the camera optics again.

•

Erase the three markings on the monitor.

•

Switch fluoro on briefly and mark the new 0° position.

•

Rotate the camera to the -220° position.

•

Mark the center on the monitor.

•

Rotate the camera to the + 220° position.

•

Mark the center on the monitor.

Fig. 8

X-ray radiation!
See Chapter 1, Safety Information.

Use radiation protection! Wear a lead apron.

WARNING

«
...
86
87
88
89
90
...
»

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments