Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 69 | Manualshive

Page: 69 / 128

Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 69

Replacing boards / replacing components

6 - 3

Siemens AG

SPR2-230.061.01

Page 3 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Replacing the

VIDEOMED DC

6

•

Move the I.I. into the service position. Refer to chapter 1.

•

Remove the cable ties at the VIDEOMED DC board. Refer to the arrow /Fig. 1).

•

Remove the connection between the VIDEOMED DC and the Compact optics.

•

Unlock the plug for the cable spool and pull it out.

•

Remove the locking screw for the VIDEOMED DC.

•

Remove the VIDEOMED DC.

Camera rotation 0° position

6

•

Connect an ohmmeter to the actual value potentiometer of the Compact optics at points
2 and 3.

•

Turn the Compact optics by the clamping ring (slowly), until the ohmmeter displays
5000 ohms + 40 ohms (0° Position). Do not adjust the camera rotation any further.

•

Install the new Videomed DC at the 0° position and tighten the clamp. The center of the
plug is in the 0° position, exactly centered to the I.I. housing. Refer to Fig. 1.

•

Reconnect the plug for the cable spool.

Fig. 1

Risk of injuries on mechanical parts!
If not observed, slight to medium injuries, especially to the hands,
can occur.

Observe the notes concerning the C-arm carbon fiber structure.

When removing or installing the VIDEOMED DC, make sure that
there are no dust or dirt particles on the optics.

0° Position

WARNING

NOTE

«
...
67
68
69
70
71
...
»

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments