Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 65 | Manualshive

Page: 65 / 128

Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 65

Adjustments / Programs

5 - 29

Siemens AG

SPR2-230.061.01

Page 29 of 30

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Configuring the MEMOSKOP

5

MEMOSKOP C-E, keyboard emulation

5

There is no keyboard supplied with some SIREMOBIL Iso-C units and installed
MEMOSKOP C-E.
When replacing the MEMOSKOP C-E or when changing the configuration, the
MEMOSKOP service program should be used.

The help file "C-DATA.hlp" will be copied to the service PC during installation of the
MEMOSKOP service program. The "C-DATA.hlp" help file contains descriptions of the
programming.

Configuring the video frequency

5

After replacing the MEMOSKOP, it will start at a default video frequency (50 Hz). If the
monitors were configured for a different frequency, you will have to configure the
MEMOSKOP.

Without installed MEMOSKOP keyboard:

•

Use the MEMOSKOP service program to modify the configuration.

With installed MEMOSKOP keyboard:

•

Invoke Technical Setup on MEMOSKOP (press the CTRL + T keys).

•

Press the "2" key and press return. The video frequency menu is selected.

•

Depending on the required video frequency, press the right cursor key "->".

"->" = Press the right cursor key

"<-" = Press the left cursor key

Roadmap K-factor, phase B

Noise suppression, phase B, is programmed in the road-
map mode.
Phase B: Acquisition of fill images.

Roadmap K-factor, phase C

Noise suppression, phase C, is programmed in the road-
map mode.
Phase C: Acquisition of roadmap images.

Roadmap Time of phase A

The time of phase A in the roadmap mode is programmed.
Phase A: Mask acquisition.

(1) in menu Diagnostics

"->" pressed 1 time:
"->" pressed 2 times:
"->" pressed 3 times:
"->" pressed 4 times:

60 Hz video frequency
100 Hz video frequency
120 Hz video frequency
50 Hz video frequency

Key "->":

(Start

"->"

"->"

"->"

"->"

...

Video frequency

50 Hz

60 Hz

100 Hz 120 Hz 50 Hz

etc...

Key "<-":

"<-"

"<-"

"<-"

"<-"

"<-"

"<-"

Function:

Comments:

«
...
63
64
65
66
67
...
»

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments