manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 62 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 62

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 26 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 26

Adjustments / Programs

 

Overview of SIREMOBIL Iso-C Parameters 

5

Invoke the Moreinfo.hlp help file on the service PC for a short description of the parame-
ters available on the SIREMOBIL Iso-C.

Overview of MEMOSKOP C / C-E / C-SUB / C & MOD / C-SUB & 
MOD Parameters

5

User Setup

•

The User Setup is invoked with the CTRL + U key combination.

•

The available functions are described in the SIREMOBIL Iso-C Operating Instructions.

Technical Setup

•

The technical setup is invoked with the CTRL + T key combination.

•

Enter the password and confirm with [RETURN] 

The following functions can be invoked depending on the type of MEMOSKOP:

If parameters have been changed and saved in the 
"Adjustments, Parameter" menu with Save to file, you must exit 
the service program with "Logoff" and "Quit" to save the modified 
parameters to the disk.

Function:

Comments:

Test pattern generation

Not for service, invoke the necessary test images on the 
service PC.

Video frequency 

The currently programmed frame rate is shown in the 
parentheses to the right. After downloading the 
MEMOSKOP or after replacement, the MEMOSKOP will 
start up at the default video frequency (50 Hz).
If the monitors are configured for a different video fre-
quency, you must perform "blind" configuration for the cor-
rect video frequency.
Refer to Configuring video frequency.

Number of monitors

Allows you to program the number of monitors used (1 or 2) 

Hardcopy setup

You can configure the connection for hardcopy cameras. 
Check whether 5000 is programmed for "4 Max Hardcopy 
time" and if not, program this value.

Edge 1 coef set

Allows configuration of edge enhancement. Check whether 
3 is programmed and if not, program this value.

Edge 2 coef set

Allows Configuration of edge enhancement. Check whether 
8 is programmed and if not, program this value.

Motion detection setup

Configures the motion detector.
Check if at MD 1: Threshold 100 and at MD 2:Threshold 
120 is programmed, if not, program these values.

Circular mask setup

Allows you to configure the diameter of the circular mask.

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments