Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 58

Page: 58 / 128

SIREMOBIL Iso-C

SPR2-230.061.01

Page 22 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 22

Adjustments / Programs

Checking the programmed values

Prerequisites

The

value is already programmed. Refer to Programming.

•

Connect the service PC to the serial interface of the SIREMOBIL Iso-C.

•

Start the service program.

•

Select the Adjustment, Calibrations menu.

•

Click "Yes" to answer the query.

•

In the Combo box "Function Group:", select "Diamentor".

•

In the window "Available Functions" , select the line "Start Diamentor Test" and click on
"Execute" .

•

Close the status window by clicking on the Ok button.

•

Respond to the query "Do you want to reset the unit" by clicking "No".

•

Press the -0- key (reset key for fluoroscopic timer).

•

The tested

value is displayed on the monitor of the SIREMOBIL Iso-C.

•

This value must match the programmed CONSTANT (Qt*Kg) value. Tolerance: + 5 %.

•

By pressing the -0- key (reset key for fluoroscopic time) the test is repeated and is dis-
played again on the monitor.

Fig. 7

Checking the programmed values will activate the self-test in the
electronic system of the area dose product measurement device.
This serves to recalibrate the electronic system of the area dose
measurement device.

Potentiometer

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Search results

Summary of Contents for SIREMOBIL Iso-C

Reviews:

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 58 / 128

Search results

Summary of Contents for SIREMOBIL Iso-C

Reviews: