manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 55 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 55

Adjustments / Programs

5 - 19

Siemens AG

 

SPR2-230.061.01

Page 19 of 30

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

Camera rotation

5

Fig. 3

Fig. 4

Fig. 5

X-ray radiation!
See Chapter 1, Safety Information.

Observe the need for radiation protection. Wear a lead apron.

The keys for horizontal and vertical image reversal must be off 
prior to adjusting camera rotation. Camera rotation should be set 
in the 0° position. Fig. 3, Fig. 4 and Fig. 5 shows the 0° position.

With the right camera rotation key (the arrow on the key is point-
ing clockwise), the marker on the monitor will rotate clockwise. 
The image contents will rotate counterclockwise.

WIth the left camera rotation key (the arrow on the key is pointing 
counterclockwise), the marker superimposed on the monitor will 
rotate counterclockwise. The image contents will rotate clock-
wise.

Patient right position

Patient left position

WARNING

NOTE

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments