manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 54 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 54

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 18 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 18

Adjustments / Programs

 

Save values and end adjustment

5

•

In the "Available Functions:" window select "INIT OFF & STORE VALUES" and click on 
"Execute". Close the status window by clicking on the "OK" button. 
For the query "Do you want to reset the Unit", click on "Yes".

Concluding tasks

5

•

Before exiting the service program, save the new parameter values to disk 
(Service PC, Data menu, Backup).

Correction of the 0° position of the slot diaphragm display

5

•

Select the "Adjustments", "Parameter" menu at the service PC. 

•

Select "Screen display Slot diaphragm" in the Combo box. 

•

Click "Get from Unit".

•

Select "Rotation 0 degree position".

•

The parameter in the "Value Actual" field can be changed according to the minimum and 
maximum values. 

•

Then click "Set Value".

•

Click "Put to Unit".

•

After the SIREMOBIL Iso-C has booted, compare the 0° position of the slot diaphragm 
blades to the display on the monitor. If necessary, repeat the programming. 

•

Click "Save to file".

•

Leave the service program with "Logoff" and "Quit" to save the parameters as a new file 
to disk. 

Correct only if the slot diaphragms are shown at an angle of rota-
tion different from that displayed on the monitor. A correction of
+ 10° is possible. Camera rotation and slot diaphragm have to be 
set correctly.

The service PC is connected to the serial interface of the 
SIREMOBIL Iso-C.

The service program is started.

NOTE 

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments