manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 20 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 20

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 12 of 18

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

1 - 12

Prerequisites

 

Cover over the horizontal carriage

1

Removing the cover

1

•

Loosen the 6 mounting screws (1/Fig. 2).

•

Expand the cover at the rear end in the direction of the arrow (see Fig. 2) and remove it 
downwards. 

•

If needed disconnect the protective ground wire, the cable of the keypad (brake buttons) 
and the cable of the emergency stop button.

Fig. 5

Fig. 6

Danger of injury when dismantling / assembling mechanical 
parts! Non-compliance can lead to minor up to moderately severe 
injuries, especially to the hands!

The cover over the horizontal carriage is bent U-shaped and must 
be pulled on the side to the outside when it is removed. 
The cover is then under mechanical stress. 

We recommend that you wear light working gloves to avoid inju-
ries.

CAUTION

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments