Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 123 | Manualshive

Page: 123 / 128

Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 123

Brakes / Movements

7 - 9

Siemens AG

SPR2-230.061.01

Page 9 of 10

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Tensioning the drive belt

7

•

Move the C-arm to the middle orbital position.

•

Remove the C-arm counterbalance weight on one side of the C-arm.

•

Slacken the drive belt (1/Fig. 9).

•

Loosen the holder of the drive belt (1/Fig. 10).

•

Adjust the drive belt in the holder by one tooth to tension it. Then fasten it again.

•

Reattach the holder of the drive belt.

•

Tension the drive belt (1/Fig. 9).

•

Reinstall the C-arm counterbalance weight.

•

Repeat the procedure at the other end of the C-arm.

Fig. 9

Fig. 10

Risk of injuries on mechanical parts!
If not observed, slight to medium injuries, especially to the hands,
can occur.

Observe the notes concerning the C-arm carbon fiber structure.

Risk of injury!
Noncompliance can lead to medium to severe injuries and/or
property damage.

The C-arm covers contain counterbalance weights and weigh
approx. 6 kg.
Hold the covers firmly when installing or removing them.
Before the C-arm cover will be loosened, the C-arm must be
moved to its middle orbital position.
If the C-arm covers are loosened, the C-arm may not be moved to
its orbital end positions (I.I. or SIREPHOS at the orbital end posi-
tion).

1

1

WARNING

WARNING

«
...
121
122
123
124
125
...
»

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments