manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Service Instructions Manual, Page: 102 / 128

Share
Download
Siemens SIREMOBIL Iso-C Service Instructions Manual Download Page 102

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 36 of 48

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

6 - 36

Replacing boards / replacing components

 

Video switcher

6

•

Switch the system off.

•

Loosen the four fastening screws of the securing bracket (1/Fig. 9).

•

Loosen the two clamping screws, but do not unscrew them completely (2/Fig. 9).

•

Tip the holding plate with the video switchers into the monitor trolley compartment 
(see Fig. 10).

•

Unplug the connectors of the video switcher to be replaced.

•

Pull the video switcher to be replaced out of the holding plate from the side.

•

Depress the green button on the video switcher. 

•

Push the new video switcher into the holding plate and reconnect all connectors.

•

Screw the holding plate back onto the monitor trolley.

•

Tighten the two clamping screws again.

•

Switch the system on. 

•

After the system run-up, the SIMOMED HM Monitor (reference monitor) should display 
the MEMOSKOP reference image. If the run-up process of the 3D reconstruction PC or 
the syngo interface appears, the green button of video switcher 1 is in the wrong position 
and needs to be switched over. (3/Fig. 9) points to video switcher 1.

•

Perform the IQ quick test.

Fig. 9

Fig. 10

Only applies to SIREMOBIL Iso-C 3D.

Video switcher 1 (3/Fig. 9) is used to switch the video signal 
between the MEMOSKOP and the 3D reconstruction PC. 
Video switcher 2 (1/Fig. 10) is used to route the video signal to the 
video printer.

1

3

1

1

2

1

1

NOTE

NOTE

Summary of Contents for SIREMOBIL Iso-C

































































































































Reviews:

No comments