Siemens SIREMOBIL Iso-C 3D Installation Instructions Manual Download Page 24

Page: 24 / 98

SIREMOBIL Iso-C 3D

SPR2-230.814.01

Page 12 of 14

Siemens AG

Rev. 05

08.04

CS PS 24

Medical Solutions

2 - 12

Actions up to serial number 1408

Orbital drive

•

Move the X-ray tube assembly at the C-arm to the end stop.

•

Remove the 3 Allen screws (Fig. 28).

•

Clean the thread of the connecting piece with the cleaning agent supplied (Fig. 29).
The thread has to be completely free of grease before it is glued in.

•

A 6 mm hexagonal insert, the required torque wrench and a suitable screwdriver for the
connecting piece should be at hand.

•

Set the torque wrench to 8 Nm.

•

The opening at the cable module has to point upward for the installation of the
connecting piece (C-arm angulation must be 90°).

Please read through the entire instructions prior to performing the
work described. Loctite bonds very quickly!

Fig. 28 Remove Allen screws

Fig. 29 Connecting piece

NOTICE

remove

Summary of Contents for SIREMOBIL Iso-C 3D



































































































Search results

Summary of Contents for SIREMOBIL Iso-C 3D

Reviews:

Siemens SIREMOBIL Iso-C 3D, Installation Instructions Manual, Page: 24 / 98

Search results

Summary of Contents for SIREMOBIL Iso-C 3D

Reviews: