manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 55 / 86

Share
Download
Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 55

Replacing boards / replacing components

6 - 3

Siemens AG

 

SPR2-130.061.02

Page 3 of 28

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

 

VIDEOMED DC

6

•

Set the camera rotation to the 0° position and mark the position of the VIDEOMED DC 
relative to the rotating I.I. optics.

•

Switch the system OFF and wait approximately 3 minutes for the anode voltage of the I.I. 
mini voltage supply to drop.

•

Disconnect the I.I. anode cable from the I.I. mini voltage supply. 

•

Make sure to short out the residual charge to ground. 

•

Ensure the correct high tension cable lengths by marking the position of the mounting 
cap nut on the anode cable with a colored pencil or electrical tape.

•

Remove the O-ring and the cap nut from the anode cable.

•

Disconnect the cable from the VIDEOMED DC and the Compact optics.

•

Cut the cable ties securing the cable.

•

Replace the VIDEOMED DC. Ensure that the VIDEOMED DC is at the 0° position rela-
tive to the rotating I.I. optics.

•

Reconnect the VIDEOMED DC - Compact optic cable and secure it with a cable tie.
Make sure that the cable does not protrude past the edge of the board. It must lie in the 
recess of the VIDEOMED DC board.

•

Reroute the anode cable to the I.I. mini voltage supply.

•

Reinstall the cap nut (as marked).

•

Reinstall the O-ring.

•

The distance from the cap nut to the beginning of the white insulation of the anode cable 
should be 70 mm.

•

Reconnect the anode cable and secure it.

•

Check the camera rotation and adjust it if necessary. 
The camera should 220°+ 3° or - 220° -3° (check this using the display).

•

Check the dose rate and adjust it if necessary.

•

Check the image sharpness with the IQ Quick test and, if necessary, adjust it at the I.I. 
optics.

•

Perform the IQ Quick test.

Power supply M14, +5 V / +15 V / -15 V

6

•

Replace the power supply.

•

Check the power supply voltage and adjust it if necessary. Refer to Chapter 3 of these in-
structions and check the operating voltages.

Electrical voltage!
See Chapter 1, Safety Information.

Switch the system power supply off and disconnect the power 
plug.

WARNING

Summary of Contents for SIREMOBIL Compact L























































































Reviews:

No comments