Siemens SIREMOBIL Compact L Service Instructions Manual Download Page 31

Page: 31 / 86

Adjustments / Programs

5 - 9

Siemens AG

SPR2-130.061.02

Page 9 of 30

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

Setting the maximum skin dose rate

Prerequisites

•

You must program one of the FL curves S2, HC2 or IODINE.

•

The FL curves S2, HC2 or IODINE should be used for the following adjustment.

•

The X-ray tube cover must be installed.

•

Use the dose ionization chamber of the dose measurement device to measure dose
rates greater than 10 R/min.

•

If you are using an area dose product measurement device, mount the dose measure-
ment chamber above the radiation exit port of the SIREPHOS.

X-ray radiation!
See Chapter 1, Safety Information.

Protect yourself against radiation exposure. Wear a lead apron.

Setting the maximum skin dose rate is necessary only for coun-
tries where DHHS regulations apply.

Fig. 2

If the maximum tube current was already reduced, the mA value
displayed at 110 kV should be recorded and used for the calcula-
tion. The maximum skin dose rate to be set should equal 9 R/min.

WARNING

NOTE

Preparations

•

Attach the dose ionization chamber at a
distance of 30 cm from the I.I. housing
(Fig. 2).

•

Select one of the FL curves S2 / HC2 or
IODINE according to the programming.
(Push-key)

•

Briefly release fluoro.

•

Select kV stop mode and enter 110 kV
(5 mA).

30 cm

Input

screen

Chamber

Holder

Sirephos

NOTE

Summary of Contents for SIREMOBIL Compact L























































































Search results

Summary of Contents for SIREMOBIL Compact L

Reviews:

Siemens SIREMOBIL Compact L, Service Instructions Manual, Page: 31 / 86

Search results

Summary of Contents for SIREMOBIL Compact L

Reviews: