Siemens SIPART PS100 Compact Operating Instructions Download Page 50

Page: 50 / 54

9.8.2

SITRANS AW050 Bluetooth adapter

Operating conditions and structural design

Ambient conditions

For use indoors and outdoors.

Ambient temperature

Observe the maximum permissible ambient temperature for
the field device.

• Permissible ambient temperature for operation

-40 ... +80 °C (-40 ... +176 °F)

• Relative humidity

0 ... 100%

Degree of pollution standard IEC 61010-1

Overvoltage category

Weight

60 g

Degree of protection

• Type 4X, Type 6 according to UL 50E
• IP66, IP68 according to IEC 60529

EMC

EN 61326

Input voltage range

2.2 ... 3.4 V DC

Maximum current consumption

2.5 mA

Material

Polycarbonate

Torque for cable gland

Corresponds to the specifications in the technical specifica‐
tions in the section Mechanical construction (Page 45)

Communication, interface

BLE 4.2

Range

Class 2; approx. 10 m depending on mounting position

Radio approval

Contains FCC ID: RYYEYSHJN
Contains IC ID: 4389B-EYSHJN
CMIIT ID: 2020DJ15120

See also

Certificates (

http://www.siemens.com/processinstrumentation/certificates

)

Technical specifications
9.8 Mobile IQ app and AW050 Bluetooth adapter

SIPART PS100

Compact Operating Instructions, 05/2021, A5E50188940-AA

Summary of Contents for SIPART PS100























































Search results

Summary of Contents for SIPART PS100

Reviews:

Related manuals for SIPART PS100

Brands by name

Popular brands

Siemens SIPART PS100, Compact Operating Instructions

Search results

Summary of Contents for SIPART PS100

Reviews:

Related manuals for SIPART PS100

Brands by name

Popular brands