Siemens SION 3AE6113-0 Operating Instructions Manual Download Page 53 | Manualshive

Page: 53 / 60

background image

Maintenance

9229 0020 176 0B

53

2019-04-02

Disposal

The materials of the vacuum circuit-breaker should be recycled. Disposal of the vac-
uum circuit-breaker with minimum environmental impact is possible on the basis of
existing legal regulations.

Metal

The circuit breaker's metal components can be recycled as mixed scrap, although it
is more environmentally sustainable to dismantle the unit as thoroughly as possible
into sorted scrap and residual mixed scrap.

Electronics

Electronic scrap must be disposed of in accordance with applicable regulations.

Materials

The vacuum circuit-breaker consists of the following materials:
• Metals

- Steel (partly phosphatised, galvanized and yellow chromated or thick layer

passivated)

- Copper (partly silver-plated)
- Aluminium (partly silver-plated)
- Brass
- Chrome

• Insulating material (partly glass fibre reinforced)

- Epoxy resin, polyester resin, polyamide, polycarbonate, ABS-PC mixture
- Silicone
- Rubber

• Ceramics
• Lubricant

For more information regarding declared or restricted substances in this product,
send an email to:
[email protected]

Packaging

If the packaging is no longer needed, it can be fully recycled.

Hazardous substances

When delivered by Siemens, the product does not contain any hazardous substanc-
es within the scope of the Hazardous Substances Ordnance applicable to the terri-
tory of the Federal Republic of Germany. For operation outside the Federal Republic
of Germany, the applicable local laws and regulations must be complied with.

Further information

Contact your Siemens Service Centre if you require further information.

Service

Contact person for service work (24 h):

Global customer service

• Telephone: +49 180/524 7000
• Fax: +49 180/524 2471
• on the internet under web address www.siemens.com/energy-support
• by email: [email protected]
Calls are not free and prices depend on the relevant provider.

Contact person for service during local business hours:

Customer service Brazil

• Telephone: +55 11 4585 8040
• by email: [email protected]

Customer service India

• Telephone: +91 1 800 419 7477
• by email: [email protected]

«
...
51
52
53
54
55
...
»

Summary of Contents for SION 3AE6113-0





























































Reviews:

No comments

Related manuals for SION 3AE6113-0

Brand: Eaton Pages: 3

Brand: CHINT Pages: 10

Brand: GE Pages: 46

Brand: GE Pages: 44

Brand: Powell Pages: 71

DL10 Series DL107

Brand: Di-LOG Pages: 12

Brand: nader Pages: 33

Brand: IDEAL Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands