Siemens SINAMICS S220 Equipment Manual Download Page 93

Page: 93 / 156

6.2

Accessories for Smart Line Modules

6.2.1

Connection plug

The line supply cable is connected to the Smart Line Module using a connection plug (power
connector).

WARNING

Electric shock or fire caused by using non-certified plug connectors

Using non-certified plug connectors to connect the power can result in overheating with
associated fire or electric shock.
• Only use approved plug connectors to connect the power.

6SL5166-2NA

0-0AA0

Connection type: Screw connection
The connection plug is included in the scope of supply
of the component and does not have to be ordered
separately.

6.2.1.1

Pin assignment

①

U1, V1, W1

②

Catch

③

Protective conductor connection

Terminal

Function

Technical specifications

Line connection

Screw terminal

V1
W1

Protective conductor connec‐
tion at the power plug

Conductor cross-section for cables with conduc‐
tor end sleeves

6 … 16 mm

AWG 6 ... AWG 10

Accessories

6.2 Accessories for Smart Line Modules

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Summary of Contents for SINAMICS S220





























































































































































Search results

Summary of Contents for SINAMICS S220

Reviews:

Siemens SINAMICS S220, Equipment Manual, Page: 93 / 156

Search results

Summary of Contents for SINAMICS S220

Reviews: