manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 120 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 120

8.5

Layout of the components

8.5.1

General information

The arrangement of the components and equipment depends on the following conditions:

• Space requirements

• Cable routing

• Bending radii of the connecting cables (MOTION-CONNECT cables, refer to Catalog D21.4 or 

NC62)

• EMC

The components of the drive lineup should preferably be installed on a conductive mounting 
surface to ensure low impedance between the component and the mounting surface. Mounting 
plates with a galvanized surface are suitable. 

Components are usually located centrally in a cabinet. The ventilation clearances required above 
and below the components can possibly exceed the minimum clearances specified in the 
manual.

The components can be arranged in one or more tiers. In a multiple-tier arrangement, vertical 
mounting or, in a cabinet row, side-by-side mounting in different cabinet sections is possible.

The DC link busbar current-carrying capacity, which is specified in the relevant technical data, is 
used to determine the cross-section. You must maintain a ventilation clearance of 100 mm 
around the line reactor (not including the mounting surface).

Support relating to the mechanical control cabinet design is available from:

Siemens AG
Digital Industries, DI MC MF -  WKC
TCCCC (Technical Competence Center Cabinets Chemnitz)
E-mail: [email protected]

8.5.2

DC link busbar current-carrying capacity

Carefully observe the current-carrying capacity of the DC link busbar when engineering and 
installing the drive lineup. The maximum current-carrying capacity of the DC link busbar differs 
for the components.

Table 8-6

Current-carrying capacity of the DC link busbars

DC link busbar or bridge

Maximum current-carrying capacity [A]

S220 Smart Line Modules 16 kW and 24 kW (100 mm)

200

Control cabinet design and EMC booksize
8.5 Layout of the components

Booksize power units

118

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments