manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 103 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 103

DC link components

7

7.1

Description

DC link components are installed in addition to the Line Modules and Motor Modules. They are 
connected to other components via the DC link.

Additional information on the DC link components is provided in Chapter "DC link components" 
of the SINAMICS S120 Equipment Manual Booksize Power Units (

https://

support.industry.siemens.com/cs/ww/en/view/109781351

).

Component

Function

Braking Modules or 
Braking Modules Compact

Stopping the drives in the event of a power failure and limiting the DC link 
voltage

Capacitor Module

Increases the DC link capacitance to buffer brief line supply failures.

Control Supply Module

Generates a 24 V DC output voltage for the other components in the 
drive lineup.
The Control Supply Module requires its own dedicated AC supply when 
starting.

SITOP PSU400M

Generates a 24 V DC output voltage for the other components in the 
drive lineup from the DC link.

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

101

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments