Siemens SINAMICS G130 TM150 Operating Instructions Manual Download Page 25

Page: 25 / 28

Electrical installation

4.4 Protective conductor connection and shield support

Terminal Module 150 (TM150)
Operating Instructions, 11/2017, A5E03758735A

4.4

Protective conductor connection and shield support

The following diagram shows a typical Weidmüller shield connection clamp for the shield

supports.

①

Protective conductor connection M4/1.8 Nm

②

Shield connection terminal, Weidmüller company, type: KLBÜ CO1, order number:

1753311001

Figure 4-4

Shield support and protective conductor connection of the TM150

NOTICE
Damage or faulty operation due to incorrect shielding or inadmissible cable lengths
If the correct shielding procedures or the permissible cable lengths are not observed, it can

cause damage or the machine may malfunction.

•

Only use shielded cables.

•

Do not exceed the cable lengths stated in the technical specifications.

Summary of Contents for SINAMICS G130 TM150





























Search results

Summary of Contents for SINAMICS G130 TM150

Reviews:

Related manuals for SINAMICS G130 TM150

Brands by name

Popular brands

Siemens SINAMICS G130 TM150, Operating Instructions Manual

Search results

Summary of Contents for SINAMICS G130 TM150

Reviews:

Related manuals for SINAMICS G130 TM150

Brands by name

Popular brands