Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 90

Page: 90 / 346

Adapting the terminal strip

5.3 Digital outputs

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

5.3

Digital outputs

Digital output terminals

Changing the function of the digital output

'21&
'212
'2&20

'212
'2&20

BO: ryyxx.n

p0731

p0730

'21&
'212
'2&20

p0732

Interconnect the digital output with a binector output of your

choice.
Binector outputs are designated with "BO" in the parameter

list of the List Manual.

Table 5- 3

Binector outputs of the inverter (selection)

Deactivating digital output

r0052.9

Process data control

r0052.0

Drive ready

r0052.10

f_actual >= p1082 (f_max)

r0052.1

Drive ready for operation

r0052.11

Alarm: Motor current/torque limit

r0052.2

Drive running

r0052.12

Brake active

r0052.3

Drive fault active

r0052.13

Motor overload

r0052.4

OFF2 active

r0052.14

Motor CW rotation

r0052.5

OFF3 active

r0052.15

Inverter overload

r0052.6

Closing lockout active

r0053.0

DC braking active

r0052.7

Drive alarm active

r0053.2

f_actual > p1080 (f_min)

r0052.8

Setpoint/actual value discrepancy

r0053.6

f_actual ≥ setpoint (f_setpoint)

A complete list of the binector outputs is provided in the List Manual.

Table 5- 4

Example:

r0052.3

52.3

p0731

Signal fault via digital output 1.

Advanced settings

You can invert the signal of the digital output using parameter p0748.
For more information, see the parameter list and the function block diagrams 2230 ff of the

List Manual.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 90 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: