manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 288 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 288

Alarms, faults and system messages 

 

9.1 Operating states indicated on LEDs 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

286

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

9.1

 

Operating states indicated on LEDs 

The LED RDY (Ready) is temporarily orange after the power supply voltage is switched-on. 

As soon as the color of the LED RDY changes to either red or green, the LEDs signal the 

inverter state.  

Signal states of the LED 

In addition to the signal states "on" and "off" there are two different flashing frequencies: 

6ORZIODVKLQJ
4XLFNIODVKLQJ

V

 

Table 9- 1 

Inverter diagnostics 

LED  

Explanation 

RDY 

BF 

 

GREEN - on 

--- 

There is presently no fault 

GREEN - slow 

--- 

Commissioning or reset to factory settings 

RED - fast 

--- 

There is presently a fault 

RED - fast 

RED - fast 

Incorrect memory card 

Table 9- 2 

Communication diagnostics via RS485 

LED BF  

Explanation 

On 

Receive process data 

RED - slow 

Bus active - no process data 

RED - fast 

No bus activity 

Table 9- 3 

Communication diagnostics via PROFIBUS DP 

LED BF  

Explanation 

off 

Cyclic data exchange (or PROFIBUS not used, p2030 = 0) 

RED - slow 

Bus fault - configuration fault 

RED - fast 

Bus fault  

- no data exchange 

- baud rate search 

- no connection  

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments