manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 24 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 24

Description 

 

2.1 Modularity of the converter system 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

22

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

Tools to commission the inverter  

,23

+DQGKHOG

,23

%23

 

Figure 2-1 

Tools to commission the inverter 

Table 2- 1 

Components and tools for commissioning and data backup 

Component or tool 

Order number 

BOP-2 - for snapping onto the frequency converter 

•

 

Copies drive parameters 

•

 

Two-line display 

•

 

Guided commissioning 

6SL3255-0AA00-4CA1 

IOP - to snap onto the frequency converter or with the handheld 

•

 

Copies drive parameters 

•

 

Plain text display 

•

 

Menu-based operation and application wizards 

6SL3255-0AA00-4JA0 
IOP Handheld: 

6SL3255-0AA00-4HA0 

Operator panel for 

commissioning, 

diagnostics and 

controlling 

frequency 

converters  

IOP/BOP-2 Mounting Kit IP54/UL Type 12 

6SL3256-0AP00-0JA0 

STARTER commissioning tool (PC software)  

 connected to the frequency converter via USB cable 

STARTER on DVD: 

6SL3072-0AA00-0AG0 
Downloading: STARTER 

(

Tools for the PC 

PC Connection Kit 

The kit contains a STARTER DVD and USB cable 

6SL3255-0AA00-2CA0 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments