manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 211 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 211

 

Functions 

 

7.6 Motor control 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

209

 

 

 

 

Note 
Only increase the voltage boost in small steps until satisfactory motor behavior is reached. 

Excessively high values in p1310 ... p1312 can cause the motor to overheat and switch off 

(trip) the inverter due to overcurrent .  

 
 

Table 7- 25  Optimizing the starting characteristics for a linear characteristic 

Parameter   Description  
P1310 

Permanent voltage boost (factory setting 50 %) 
The voltage boost is active from standstill up to the rated speed. 

It is at its highest at speed 0 and continually decreases as the speed increases.  

Value of voltage boost at zero speed in V:  

1.732 × rated motor current (p0305) × stator resistance (r0395) × p1310 / 100 %.  

P1311 

Voltage boost on acceleration 
The voltage boost on acceleration is independent of speed and occurs when the 

setpoint is increased. It disappears as soon as the setpoint is reached.  

Value in V: 1.732 × rated motor current (p0305) × stator resistance (r0395) x p1311 / 

100 % 

P1312 

Voltage boost at start up 
The voltage boost at start-up results in an additional voltage boost when accelerating, 

but only the first time the motor accelerates after it has been switched on. 

The voltage boost in V is: 1.732 x rated motor current (p0305) × stator resistance 

(r0395) x p1312 / 100% 

You will find more information about this function in the parameter list and in function 

diagram 6300 of the List Manual.  

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments