Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 103

Page: 103 / 346

Configuring the fieldbus

6.1 Communication via PROFIBUS

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

101

6.1.4

Cyclic communication

The PROFIdrive profile defines different telegram types. Telegrams contain the data for

cyclic communication with a defined meaning and sequence. The inverter has the telegram

types listed in the table below.

Table 6- 3

Inverter telegram types

Telegram type (p0922)

Process data (PZD) - control and status words, setpoints and actual values

PZD01
STW1
ZSW1

PZD02
HSW
HIW

PZD03

PZD04

PZD05

PZD06

PZD07

PZD08

STW1 NSOLL_A ⇐ The inverter receives this data from the control

Telegram 1

Speed control

PZD 2/2

ZSW1 NIST_A

⇒ The inverter sends this data to the control

STW1 NSOLL_A

Telegram 20

Speed control, VIK/NAMUR

PZD 2/6

ZSW1 NIST_A_

GLATT

IAIST_

GLATT

MIST_

GLATT

PIST_

GLATT

MELD_

NAMUR

STW1 NSOLL_A M_LIM

STW3

Telegram 350

Speed control

PZD 4/4

ZSW1 NIST_A_

GLATT

IAIST_

GLATT

ZSW3

STW1 NSOLL_A

PCS7 process data

Telegram 352

Speed control, PCS7

PZD 6/6

ZSW1 NIST_A_

GLATT

IAIST_

GLATT

MIST_

GLATT

WARN_

CODE

FAULT_

CODE

STW1 NSOLL_A

Telegram 353

Speed control,

PKW 4/4 and PZD 2/2

ZSW1 NIST_A_

GLATT

STW1 NSOLL_A

PCS7 process data

Telegram 354

Speed control,

PKW 4/4 and PZD 6/6

ZSW1 NIST_A_

GLATT

IAIST_

GLATT

MIST_

GLATT

WARN_

CODE

FAULT_

CODE

STW1 Telegram length on receipt can be configured up to max. 8 words

Telegram 999

Free interconnection via BICO

PZD n/m (n,m = 1 … 8)

ZSW1 Telegram length on transmission can be configured up to max. 8 words

Table 6- 4

Explanation of the abbreviations

Abbreviation

Significance

Abbreviation

Significance

STW1/2

Control word 1/2

PIST_GLATT

Actual active power

ZSW1/2

Status word 1/2

MELD_NAMUR

Control word according to the VIK-

NAMUR definition

NSOLL_A

Speed setpoint

M_LIM

Torque limit value

NIST_A_GLATT

Smoothed speed actual value

FAULT_CODE

Fault number

IAIST_GLATT

Smoothed actual current value

WARN_CODE

Alarm number

MIST_GLATT

Actual torque

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 103 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: