Siemens SIMOTION P320-4 E Manual Download Page 95

Page: 95 / 166

5.7

Ethernet

Interface assignment

Designation: PN/IND. Ethernet (LAN), X1
Type: 8-pin RJ45 socket

Ethernet RJ45 interface

/('

Pin no.

Short description

Meaning

Input/output

BI_DA+

Bi-directional data A+

Input/output

BI_DA-

Bi-directional data A-

Input/output

BI_DB+

Bi-directional data B+

Input/output

BI_DC+

Bi-directional data C+

Input/output

BI_DC-

Bi-directional data C-

Input/output

BI_DB-

Bi-directional data B-

Input/output

BI_DD+

Bi-directional data D+

Input/output

BI_DD-

Bi-directional data D-

Input/output

–

Shield

–

LED 1

Off: 10 Mbps

Green light: 100 Mbps

Orange light: 1000 Mbps

–

LED 2

Lit: Active connection, e.g., to a hub

Flashing: Activity

–

Note
The interfaces available on the device have been numbered for unique identification.
This numbering may deviate, however, from the numbering assigned by the operating system.

Interfaces

5.7 Ethernet

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

Summary of Contents for SIMOTION P320-4 E







































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands