Siemens SIMOTION P320-4 E Manual Download Page 90

Page: 90 / 166

5.3

Control elements

On/Off switch

①

Requirement:
The BIOS setup entry After Power Failure is set to Power on.
The On/Off switch is used to switch the SIMOTION P320-4 on.

Figure 5-2

SIMOTION P320-4 - operator controls

WARNING

De-energize the SIMOTION P320-4!
The On/Off switch does not disconnect the device from the power supply system.

When the switch is in position 0 (Off), the device is still supplied with mains voltage.
To remove power from the device, the power supply plug must be removed.

NOTICE
Close down the operating system first
First close down the operating system before switching off the device with the on/off switch,

otherwise data may get lost.

Interfaces
5.3 Control elements

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

Summary of Contents for SIMOTION P320-4 E







































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands