Siemens SIMOTION P320-4 E Page 138 Manual Download

Page: 138 / 166

9.4

Technical data of the IsoPROFIBUS board

Technical specifications of the IsoPROFIBUS board (optional)

Table 9-1

IsoPROFIBUS board
Power consumption for + 5 V PCI voltage
Standard

2.5 W

Maximum

3.5 W

Permissible ambient conditions
Heat dissipation

Open circuit ventilation

Temperature

Operation

Storage/transport

● IsoPROFIBUS board in the

SIMOTION P320-4

5° C to 45° C

-20° C to 60° C

Tested according to

EN 60068-2-1, EN 60068-2-2, EN 60068-2-14

Relative atmospheric humidity

Operation

Storage/transport

● IsoPROFIBUS board in the

SIMOTION P320-4

5 % … 80 %

5 % … 95 %

Tested according to

EN 60068-2-30

Temperature change

Max. 10 K per hour in operation

Moisture condensation and ice formation

Not permissible

Design
Module

Card (3.3 V/5 V, 32 bits)

Dimensions (H x D) in mm

107 x 170

Weight

150 g

Space requirements

Short PCI slot

Safety

Safety
Degree of protection

IP20 in mounted state

Protection class

I complies with VDE 0106

Safety regulations

EN 60950

Approvals

CE, UL508, cULus

Technical data
9.4 Technical data of the IsoPROFIBUS board

SIMOTION P320-4 E / P320-4 S

138

Manual, 03/2018, A5E36004933B

Summary of Contents for SIMOTION P320-4 E







































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands