Siemens SIMOTION P320-4 E Manual Download Page 105

Page: 105 / 166

Vertical mounting

The following vertical mounting option is permitted:

The interfaces are at the front. The power sup‐

ply connection is at the top.

You can find information on mounting under Vertical mounting (Page 107).

Ambient conditions

Observe the permissible temperature range for operation in the respective mounting position

as described in Section "Technical data > Ambient conditions (Page 136)".

6.2.1

Standard rail mounting and vertical mounting

6.2.1.1

Standard rail mounting

Requirement

● Standard mounting rail, 35 mm standard profile

The standard mounting rail is installed at the installation site.

● The standard mounting rail clip is attached to the SIMOTION P320-4.

Note
Ensure that the wall or ceiling can hold four times the total weight of the SIMOTION P320-4

including the standard mounting rail and additional expansion cards. See section Notes on

installation (Page 109).

Installation/mounting

6.2 Permissible mounting positions

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

105

Summary of Contents for SIMOTION P320-4 E







































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands