Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 54 / 222

Basic data
P320-4 E

2 x CFast card

Internal interface: CFast
External interface: CFast

P320-4 S

SSD (Solid State Disk)
Internal interface: SSD
CFast card
External interface: CFast

USB stick

External, can be connected via USB interface

Interfaces
Serial

COM (RS 232)

Graphics

DVI-I: Suitable for use as DVI or VGA
DPP++: Display port, DVI via DPP-to-DVI adapter

USB

4 × USB 3.0, simultaneous operation of high current,

backward compatible with USB 2.0/1.1

Ethernet

1 × RJ45 (10/100/1000 Mbps)

PROFINET I/O

3 × RJ45 (100 Mbps)

Keyboard, mouse

Can be connected via USB interface

Software
Operating systems
P320-4 E

Windows Embedded Standard 7 32-bit

P320-4 S

Windows 7 Ultimate 32-bit

Description
3.2 SIMOTION P320-4 product description

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands