Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 174 / 222

● Data that was saved with the _savePersistentMemoryData(), _saveUnitDataSet(),

_exportUnitDataSet() commands and with RAM to ROM.

If the retain data is backed up (with _savePersistentMemoryData()), this data is backed up

again to the non-volatile data after the general reset. Thus, the user can perform a general

reset to force the saved retain data to be restored.

● Licenses
The technology packages and user data (configuration data, programs, parameter

assignments) previously backed up to an external CFast card by means of the Copy RAM to

ROM menu command are transferred to the volatile data area of the SIMOTION P320‑4 after

the general reset.

Thus, an existing configuration on the external CFast card is loaded to the SIMOTION device

following the general reset.

Further information

Data storage concept overview (Page 157)

10.9.2

Overall reset using the mode selector (on screen)

For SIMOTION P320-4, the overall reset using a simulated mode selector is performed using

the SIMOTION P State application.

Note
MRES mode switch position
If you set MRES via the SIMOTION P State application, the SIMOTION P320-4 automatically

goes into the STOP operating state.

Commissioning (software)
10.9 SIMOTION P overall reset

SIMOTION P320-4 E / P320-4 S

174

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands