Siemens SIMOTION P320-3 Manual Download

Page: 98 / 150

Connecting

6.6 USB strain-relief

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

6.6

USB strain-relief

The USB strain-relief provided as an accessory is used to prevent accidental loosening of

the USB cable from the device. A cable binder (not included in the package) is needed to

use this accessory.

Required tools

To fix the USB strain relief, you will need a TORX T20 screwdriver.

Procedure

To attach the USB strain relief, proceed as follows:
1.

Fasten the USB strain-relief

①

to the device housing with an oval-head screw (M4

thread).

Thread the cable tie

②

through the comb of the USB strain-relief to fasten the USB

cable.

Figure 6-4

USB strain-relief

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands