Siemens SIMOTION P320-3 Manual Download

Page: 82 / 150

Installing/Mounting

5.2 Installing/removing an accessible CompactFlash card

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

Installing the CompactFlash card

Steps for installing a CF card
1 Open the module receptacle.
2 Insert the CF card with the connector

facing in until it locks in the slot

①

3 Close the module receptacle again.

Note
The CompactFlash slot is coded against reversed insertion of the CF card. Insert it so that its

upper side (label side) is facing the front panel of the device.

CAUTION

If the CF card meets resistance, flip it over. Never insert the CF card with force.

Removing the CompactFlash card

Steps for removing a CF card
1 Open the module receptacle.
2 Press the eject button

①

and remove

the CF card.

3 Close the module receptacle again.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands