background image

Hardware description 

 

3.5 SIMOTION panel fronts 

 

SIMOTION P320-3 and Panel Fronts 

52

 

Manual, 02/2012 

3.5

 

SIMOTION panel fronts 

3.5.1

 

Overview of SIMOTION panel fronts (hardware) 

SIMOTION panel fronts are essentially available in 2 variants: 
●  Panel with keys 
●  Panel with touch screen. 
Both variants feature status LEDs for power supply and temperature, a front-mounted USB 

interface and IP65 degree of protection. 
A panel front with a 12-inch display is available for the variant with keys. Panel fronts with 

12- or 15-inch displays are available for the touch screen variant. 

3.5.2

 

Panels with keys view 

The following figure shows the front view of the SIMOTION panel front with keys.  
The SIMOTION P012K panel front display has a resolution of 800 x 600 pixels. 

86%LQWHUIDFH

6WDWXVGLVSOD\V

'LVSOD\

)XQFWLRQNH\VVRIWNH\V

$OSKDFXUVRUDQGFRQWURONH\V
QXPHULFNH\EORFN

,QWHJUDWHGPRXVH

 

Figure 3-5 

SIMOTION panel front with keys variant 

Summary of Contents for SIMOTION P320-3























































































































































Reviews: